Most Likely Causes (Ranked)
The pressure tank (WaterWorker HT-14HB pressure tank) should be 2/3 air and 1/3 water. When the air bladder fails, the tank fills with water and can't maintain pressure. The pump turns on and off rapidly (short cycling) — clicking the pressure switch with each cycle.
The pressure switch senses line pressure and turns the pump on/off. A failing switch chatters or clicks without properly engaging.
The check valve prevents water from flowing back down the well when the pump stops. A failed check valve lets water drain back, causing the pressure to drop and the pump to restart (short cycle).
A leak anywhere in the plumbing allows pressure to drop, triggering the pump to cycle. Even a running toilet can cause short cycling.
The pump or piping has an air leak on the suction side. The pump loses its water prime, pressure drops, and the pump cycles trying to maintain pressure.
How to Fix It
Inspect and Clean the Equipment
$0 – $25Estimated time: 15-30 minutes
- 1Turn off the equipment and inspect for debris, corrosion, and loose parts. Clear leaves, dirt, and insects from intakes, screens, and moving parts. Clean all accessible surfaces. Check that all fasteners are tight. This resolves about 30% of outdoor equipment noise issues.
Lubricate Moving Parts
$5 – $15Estimated time: 10-20 minutes
- 1Apply appropriate lubricant to all moving parts: silicone spray for tracks and slides, motor oil for bearings with oil ports, lithium grease for gears and heavy-load points. Don't use WD-40 as a long-term lubricant — it's a solvent that displaces water but doesn't provide lasting lubrication.
Replace Worn Components
$20 – $300Estimated time: 30 min – 2 hours
- 1Outdoor equipment parts are readily available. Pool pump seal kits: $15-30. Motor bearings: $20-50. Pressure tank (WaterWorker HT-14HB pressure tank) bladder: $100-200. Gate hinges: $10-30. Check the manufacturer's website for exploded parts diagrams and part numbers. Many outdoor repairs are straightforward DIY projects.
Professional Service for Complex Equipment
$100 – $400Estimated time: 1-3 hours
- 1For well pumps, pool equipment, and electrical systems, professional service ensures safety and proper operation. Well pump service: $200-400. Pool equipment repair: $100-300. Sprinkler system winterization and repair: $75-200. Annual maintenance contracts are available and often cheaper than emergency calls.
When to Call a Professional
If the clicking is accompanied by a burning smell, visible damage, or the equipment stops working, turn it off immediately.
If the clicking suddenly changes character or gets dramatically louder, stop using the equipment until the cause is identified.
For any equipment connected to gas or high-voltage electrical, hire a licensed professional rather than attempting DIY repair.
How to Prevent It
Maintain outdoor equipment seasonally. Clean and inspect pool pumps, sprinkler systems, and AC units at the start and end of each operating season.
Apply silicone lubricant to moving parts (hinges, latches, slides) every 6 months to prevent squeaking and stiffness.
Inspect outdoor fasteners annually. Replace corroded screws and bolts with stainless steel or galvanized hardware.
Store portable outdoor equipment in covered areas during off-season to reduce weather exposure and extend equipment life.
Frequently Asked Questions
The most common cause of a clicking noise from a well pump is worn internal components that have developed excessive clearance or lost lubrication. Other causes include loose mounting hardware, debris interference, and normal operational sounds that may be new to you. Our guide above ranks the 5 most likely causes from most to least common, with specific diagnostic steps to identify which one matches your situation.
It depends on the specific cause. Most causes of a clicking well pump are not immediately dangerous, but ignoring the sound often leads to more expensive repairs down the road. Some causes can indicate developing safety issues. Check our warning signs section above for when to act urgently versus when it's safe to schedule service.
Costs range widely depending on the cause. Simple fixes like tightening loose hardware, cleaning filters, or replacing a belt can be $0-30 as DIY projects. Mid-range repairs like replacing a motor, pump, or bearing typically run $100-500 including parts and labor. Major repairs or replacements can be $500-3,000+. Our fix guide above includes specific cost ranges for each repair option, and our cause descriptions include part costs where applicable.
Many causes of a clicking well pump are DIY-friendly. Cleaning, tightening, lubricating, and replacing basic wear parts (filters, belts, rollers) require only basic tools. More complex repairs involving gas lines, refrigerant, high-voltage electrical, or major disassembly are best left to professionals. Our fix guide above rates each repair by difficulty and provides step-by-step guidance for DIY-appropriate fixes.